Catalinbread Cloak Room Reverb / Preamp / Shimmer Pedal

$157.49 $294.00
Maximum quantity available reached.

Sku: 853710004789
Cloak Reverb and Shimmer Pedal

Overview

The Cloak began after unearthing some ancient texts containing some forbidden incantations on how to introduce spectral elements within a decaying echo. Ok, maybe embellishing a bit; but the inspiration came from the land of academia and the acoustics department at Stanford, where a treatise on the optimal shimmer effect was penned a handful of years back. In a similar pursuit of perfection, Catalinbread drew inspiration from a combination of research and thier own endeavors to craft a truly superb take on shimmer reverb.

At its core, the Cloak is a “room” style reverb that sounds amazing on its own, but with a twist of the Shimmer knob, rich, harmonically-laden overtones creep in, emphasizing three different orders of harmonics within the trails. A specially-designed low-pass filter steps in and smooths the harmonics out before they get too out of hand and wreck up the signal path. The size of the room can be effortlessly dialed in, from a cramped broom closet to as close to infinity as can possibly be mustered. This comes in handy when deciding on which type of switching you prefer; the Cloak offers up true bypass switching that cuts off the reverb trails when the Cloak is disengaged, or buffered bypass, which keeps the decay going even after switching off—your pick. Either way you slice it, the Cloak is ready to impart a little black magic unto your rig.


Controls

ROOM SIZE: Simultaneously adjusts both reverb decay length and a slight gain enhancement for a more natural decay

MIX: Adjusts the amount of dry signal present in the output, from 100 percent dry to 100 percent wet

HIGH CUT: Cuts higher-order harmonics from the signal to soften the edges at higher Shimmer settings

SHIMMER: Mixes the amount of shimmer present in the room reverb. Fully CCW gives you a rich room reverb and fully CW serves up a harmonically rich shimmer


Under The Hood

The Cloak is shipped in trails mode. This mode is buffered, and the preamp will be active even in bypass. Catalinbread calls it "Trails" mode because the reverb signal will continue to decay even after the Cloak is switched off. Removing the back panel gives you the option to turn the Cloak into "true bypass" mode. In this mode, your signal is unaffected by the Cloak when it is turned off. However, turning off the Cloak will immediately cut off the reverb signal.


Power Supply

The Cloak runs from 9 to 18 volts using a standard DC center-negative power supply for pedals. Make sure you’re using a supply that provides at least 100mA. 9 volts will sound great all around. But if you want even more output and an even healthier boost to your dry signal with increased headroom, try all the way up to 18 volts! The Cloak does not run on batteries.

Measurements

FILTER: cutoff at 5khz and knob is how much reduction past 5k from fully open down to fully cut everything above 5k REVERB

TIME: Shortest: 250ms. Longest: (depending on how hard the signal hits but tested by smacking the strings of a guitar) >3 seconds

CURRENT DRAW: ~60mA

Designer's Notes

One night, I was relaxing and browsing a cache of old DSP papers, as one does, and one struck me in particular, this one. The paper was so eye-opening that it led me to start writing my own harmonic reverb algorithms, naturally. Having written a handful, the ones that really stood out were ones without harmonic modulation and a separate shimmer effect tailored to the base reverb sound. Combining these in a pleasing way yielded a satisfying tone but at the cost of some extreme frequency crispiness. Not good! Then again, I was testing on a Fender Princeton. After tinkering around with a couple filtering options, I decided on a bit of attenuation code that keeps a little crispiness for those using darker amps, but could also cut the high end completely for some really cool “dark shimmer” effects. I think it rules and I think you will too. – Lee Brady