Peavey 6505 II 120 Watt Tube Guitar Amplifier Head

New

Peavey 6505 II 120 Watt Tube Guitar Amplifier Head

Peavey's classic high-gain legacy continues with the 6505 II. Like the original 6505 head, the 6505 II offers two channels. However, the 6505 II adds separate EQ, Resonance, and Presence controls to each channel, giving you more control and flexibility. The new footswitch provides foot control of channel selection, effects loop, and the newly added ability to select the Crunch feature. Now you can instantly obtain that extra gain in the Rhythm Channel with your foot and never have to take your hand off the guitar. Finally, the Clean Channel has been added, completely redesigned to sound much cleaner, and has one 12AX7 devoted to just the Clean/Crunch.


Features:

• 120 watts output power
• Six 12AX7 preamp and four 6L6GC power amp tubes
• Two distinct tube channels with footswitch control
• LED "active" indicators for each channel
• Bright switch for Rhythm channel
• Crunch switch on Rhythm channel with footswitch control
• Separate equalizer sections for each channel
• Separate power amp controls (Resonance and Presence) for each channel
• Separate preamp controls (Pre and Post Gain) for each channel
• Standby power switch
• ias test points on rear panel
• Effects loop with footswitch control
• 1/4" Preamp output jack
• Speaker impedance selection switch (4, 8, 16 ohm)
• Two parallel 1/4" speaker output jacks
• Universal AC Input Selector for worldwide use
• Metal three button footswitch with detachable 25' cable


POWER AMPLIFICATION SECTION

• RATED POWER AND LOAD: 120 W RMS into 16, 8, or 4 ohms
• POWER at CLIPPING: (Typically at 5% THD, 1 kHz, 120 V AC line); 130 W RMS into 16, 8, or 4 ohms (Bias must be reduced to measure.)
• FREQUENCY RESPONSE: +0, -3 dB, 50 Hz to 20 kHz at 100 W RMS into 8 ohms
• HUM AND NOISE: Greater than 75 dB below rated power
• POWER AMP EQ: Active Presence: +10 dB at 2 kHz; Active Resonance: +10 dB at cabinet resonant frequency
• POWER CONSUMPTION (Domestic): 400 watts 50/60 Hz, 120 V AC
• TUBE COMPLEMENT: 6-12AX7 preamp tubes (1 for clean/crunch, 3 for Lead, 1 for EFX and 1 phase splitter); 4-6L6GC


PREAMP SECTION

The following specs are measured at 1 kHz with the controls preset as follows: Low and High EQ at 10; Mid EQ at 0; Bright out; Lead and Rhythm Posts at 10 ; Presence and Resonance at 0 dB ; Nominal levels with Pre Gains at 5; Minimum levels with Pre Gains at 10

PREAMP INPUT:

• Impedance: Very high Z, 470K ohms
• Lead Channel (with channel select in):
• Nominal Input Level: -60 dBV; 1 mV RMS
• Minimum Input Level: -76 dBV; .15 mV RMS
• Clean Channel (with channel select out):
• Nominal Input Level: -30 dBV; 30 mV RMS
• Minimum Input Level: -34 dBV; 20 mV RMS
• Maximum Input Level: 0 dBV; 1.0 V RMS
• (Subtract 24 dB with Crunch switch in.)


EFFECTS SEND:

• Load Impedance: 47 k ohms or greater
• Nominal Output: -10 dBV, 300 mV RMS


EFFECTS RETURN:

• Impedance: Very High Z, 470 k ohms
• Designed Level: -10 dBV, 300 mV RMS


PREAMP OUT:

• Load Impedance: 47 k ohms or greater
• Nominal Output: +10 dBV, 3 V RMS


REMOTE FOOTSWITCH INCLUDED:

• Special 3-button unit with LED indicators FOR Channel select and reverb


EQUALIZATION:

• Custom Low, Mid, and High passive type EQ
• Push Bright (Rhythm Channel only); +6 dB at 2 kHz
• Push Crunch (Rhythm Channel only); Increases gain


DIMENSIONS AND WEIGHT

• (H x W x D) 10" x 26.625" x 11.75" (25.4 cm x 67.6 cm x 29.8 cm
• 48.3 lbs. (21.91 kg)